News Center
News Center
Image Name

NEWS

News Center

09-23

2014

Shell-and-tube continuous helical baffle heat exchanger

The so‑called continuous helical baffle heat exchanger eliminates the arc‑shaped baffles traditionally used in shell‑and‑tube heat exchangers to control fluid flow direction and velocity, replacing them with continuous helical baffles—more accurately termed helical flow guides. Within the shell, these continuous helical flow guides direct the fluid along a continuous, closed spiral path whose cross‑sectional area remains constant; in other words, throughout its entire passage through the shell side, the fluid follows a stable helical trajectory. This fundamentally transforms the zigzag, back-and-forth flow pattern characteristic of conventional shell‑and‑tube heat exchangers with arc‑shaped baffles, marking a revolutionary change in the flow dynamics on the shell side. And now…


09-24

2014

Introduction to the Lengde Seawater Heat Exchanger

During the 12th Five-Year Plan period, China will enter a critical phase of strengthening its capacity to safeguard maritime rights and interests, transforming its marine economic growth model, adjusting its industrial structure, and establishing an emerging strategic marine industry system. Faced with increasingly severe challenges in maritime rights protection and marine ecological conservation, as well as the substantial demand for the development and utilization of marine resources, the marine equipment manufacturing sector is poised for rapid growth, driving robust demand for seawater heat exchange equipment. However, seawater contains high concentrations of dissolved oxygen, chloride ions, and microorganisms, which pose significant corrosive risks to metal heat exchangers. Therefore, seawater heat exchangers must address corrosion‑resistance issues. Lengde Company is dedicated to developing corrosion‑resistant heat exchangers.


09-24

2014

Discussion on Anti-Corrosion Technologies for Seawater Heat Exchangers

Corrosion is a pervasive issue across all sectors and industries, posing significant threats to national economic development, human well-being, and the environment. Corrosion frequently leads to shortened plant operating cycles, premature failure of equipment and facilities, reduced service life, and environmental pollution; it also hinders the smooth advancement of new technologies. According to statistics, annual economic losses attributable to corrosion in various countries typically account for 1% to 5% of their respective gross domestic product, varying with each country’s level of economic development and its capacity for corrosion control. In China, the losses caused by corrosion are particularly severe; according to data from the “China Corrosion Survey Report,” the country’s annual corrosion-related losses in recent years have amounted to approximately…


09-24

2014

Introduction to High-Efficiency Oil-Gas Separators

Currently, large central air-conditioning systems and low-temperature refrigeration facilities commonly employ screw-type chillers. However, screw compressors typically operate with oil‑injection, and the compressor discharge carries a portion of the refrigeration oil out of the unit. To prevent this oil from entering the system—particularly in chiller and low‑temperature freezer units that use flooded evaporators, where oil return is especially challenging—and to avoid significant adverse effects on heat‑exchanger efficiency, it is necessary to install an oil–gas separator at the compressor discharge. Although existing technologies incorporate built‑in oil–gas separators within the compressor, their separation performance remains inadequate, leaving substantial amounts of oil still present.


09-25

2014

Freeze Damage and Anti-Freeze Measures for Shell-and-Tube Heat Exchangers

Shell-and-tube heat exchangers used in refrigeration systems frequently experience failures that paralyze the refrigeration circuit and result in substantial economic losses due to tube ruptures. One of the most common causes of such tube failures is ice formation on the water side of the heat exchanger: as the ice expands, it can either burst or crush the tubes. Condensers and flooded evaporators are typically prone to tube damage caused by ice‑induced expansion, whereas dry‑type evaporators more often suffer from tube damage due to ice‑induced compression. The primary reasons for water freezing inside the heat exchanger fall into the following categories: 1. When the unit remains shut down for an extended period and the water has not been drained or has not been completely removed, any residual water within the tubes will freeze and expand upon ambient temperatures dropping below 0°C, ultimately causing the tubes to rupture. For…


09-25

2014

Design of a Water-Cooled Screw Chiller System for Air Conditioning

Common water-cooled screw chillers are primarily classified into three types based on evaporator design: dry‑type units, flooded‑type units, and falling‑film units. The core component of a water‑cooled screw chiller is the screw compressor; the market is dominated by twin‑screw compressors, with a few manufacturers opting for single‑screw models. Most compressors are semi‑hermetic, though some manufacturers also offer open‑type or fully hermetic designs. With the exception of major U.S. and Japanese brands, domestic manufacturers generally source their compressors from external suppliers. The system designs of dry‑type water‑cooled screw chillers across different manufacturers are largely similar, differing mainly in heat exchanger and throttling‑device configurations. On the market, leading manufacturers employ broadly comparable condenser designs (condensing…


< 1234 >
< 1234 >